How To Set Up Brita Pitcher

Download Commodity

Download Article

Brita pitchers filter out certain elements, such equally chlorine and copper, that don't belong in your drinking water.^[1] If you lot're concerned about what'southward in your tap water and you want to ensure that you're ingesting the healthiest water possible, filling and using a Brita pitcher might exist a step in the right direction.

1. 1

   Accept the bullpen out of its packaging. When you purchase your pitcher, take it out of the box it's in. Then, pull off the plastic that'south wrapped all effectually the bullpen and discard it. Have out any items that are inside of your pitcher, such as the manual and/or the filter, and set them aside.

2. two

   Wash and dry the pitcher. With all packaging discarded, accept apart the pitcher and place the different parts in a sink. Use a mild dish detergent, a sponge, and warm water to launder the parts. Then, dry them with a clean manus towel.^[2]

   Advertising

3. iii

   Rinse the filter under cold water for 15 seconds. Take the filter that came with your pitcher out of its packaging. Then, hold it nether common cold running water for at least 15 seconds. At this point, the filter is prepare to be used.^[3]

4. iv

   Insert the filter into the pitcher. Take the lid off of your pitcher and concur your filter by its top. Line up the groove in the filter with the notch in the hole that's located in the bottom of the reservoir. Slide the filter downward into the hole.^[4]

5. 5

   Make full the reservoir with water. With the lid still off and the filter in place, fill the reservoir completely with tap water. The water will slowly filter through and fill the bottom of the pitcher. At this point, your water will exist ready to drink.^[five]

   • In social club to fill the pitcher completely, you may need to fill the reservoir more than once.

Advertisement

1. ane

   Remove the lid and bring the pitcher to the sink. When you've drank all of the filtered water in your bullpen, accept it out of the fridge. Take the hat off and place information technology on the counter. Selection up the bullpen by the handle and concord it in the sink underneath the faucet.

2. 2

   Make full the reservoir with cold water. Fill the reservoir all of the fashion up to the top. Wait as the h2o slowly filters through into the bottom of the pitcher. In one case the reservoir is most one-half emptied, refill it to the top. This should allow the pitcher to fill up completely with filtered water.^[6]

3. 3

   Put the hat back on and return the bullpen to the refrigerator. Once the bottom of the pitcher is full of water, put the lid dorsum on. Then, put the bullpen dorsum in the refrigerator so that it stays absurd.^[seven]

   • Drink all of the filtered water in your pitcher within 1-2 days to ensure that you're consuming the freshest water possible.

4. 4

   Add tap water to the reservoir every time yous utilize it to keep it full. Instead of waiting until your pitcher is empty to refill it, refill it a little bit each fourth dimension you apply it. Every fourth dimension you take out your pitcher to pour yourself a glass of filtered water, first fill the glass with tap water and cascade it into the reservoir. This fashion, your Brita pitcher will always stay full.

   • Be careful when you lot pour yourself the glass of filtered water, as the water in the reservoir may spill out if the lid doesn't stay securely on.

Advertisement

1. 1

   Have off the hat and pull out the old filter. When it'south time to supersede your filter, you offset need to take the old one out. Take off the pitcher lid and place it aside. And then achieve into the reservoir, grab the filter by its superlative handle, and pull information technology out. Discard the onetime filter.^[eight]

2. 2

   Rinse the new filter for 15 seconds. Take your new filter out of whatsoever packaging that it came in. Hold your new filter by its top handle underneath running water for at least 15 seconds.^[nine]

3. 3

   Insert the new filter. Continue holding the new filter past its summit handle while you lucifer upwardly the notch on the pitcher with the groove that'south on the filter. And then, slide the filter down into identify.^[10]

4. iv

   Fill the reservoir will cold tap h2o. Once the new filter is securely in place, fill the reservoir to the peak with cold tap water. Your pitcher volition so be set up to use over again.^[xi]

5. 5

   Supercede Standard or Stream Brita filters every two months. If yous're using the white-colored Standard Brita filter or the gray-colored Stream Brita filter, it'll need to exist switched out later on you've filtered 40 gallons (150 l) of water through your pitcher. This should take nearly 2 months.^[12]

6. 6

   Switch out Longlast Brita filters every vi months. If you take the blue-colored Longlast Brita filter, you tin can use your filter for a longer time before it needs to exist replaced. This type of filter can filter 120 gallons (450 l) of water, which ways information technology typically lasts about 6 months.^[13]

7. 7

   Modify your Brita Smart Bullpen's filter when an arrow is displayed. If y'all accept a Smart Pitcher, the electronic indicator volition let you know when information technology's time to supervene upon the filter by displaying a flashing pointer at the meridian. After y'all've changed the filter, reset the screen by holding down the start push button for 5-x seconds, and letting go once you encounter four flashing bars.^[14]

   • If you have a hard fourth dimension property downward the start button, attempt using a capped ballpoint pen.
   • Every two weeks, one of these bars will disappear.
   • Once there'southward only 1 bar left on the screen, make certain you accept a new filter on hand.

8. viii

   Put in a new filter when the current i is filtering slowly. If yous aren't sure if you need to switch out your filter, pay attention to how long it takes to filter the water. If you notice that the filtering process takes longer than information technology used to, it may be time to replace your filter.^[15]

Advertizing

Ask a Question

200 characters left

Include your e-mail accost to get a message when this question is answered.

Submit

Advertizing

Cheers for submitting a tip for review!

About This Article

Article Summary 10

If you've never used your pitcher, unpack it, take it apart, and wash it with mild dish detergent and warm water. Dry out the pitcher with a make clean hand towel, remove the hat, and fill the reservoir with cold tap h2o. If you're just refilling your pitcher, merely remove the lid and make full the reservoir with cold tap water. To larn how to replace your filter, gyre down!

Did this summary help you?

Cheers to all authors for creating a page that has been read 94,526 times.

Did this article help you lot?

Source: https://www.wikihow.com/Use-a-Brita-Pitcher

Share this post